If an error occurred or the following message in Chinese (Simplified) language and you cannot find a solution, than check answer in English. Table below helps to know how correctly this phrase sounds in English.
| id |
Chinese (Simplified) |
English |
| 0x1CE8 | SORT [/R] [/+n] [/M kilobytes] [/L locale] [/REC recordbytes] [[drive1:][path1]filename1] [/T [drive2:][path2]] [/O [drive3:][path3]filename3] /+n 指定开始每个比较的字符号码 n。/+3 说明每个 比较应从每行的第三个字符开始。少于 n 个字符 的行排在其他行之前。按默认值，从每行的第一 个字符开始比较。 /L[OCALE] locale 用指定的区域设置替代系统默认区域设置。 \"\"C\"\" 区域设置产生最快的排序顺序并且是当前 的唯一其他选择。排序总是不分大小写的。 /M[EMORY] kilobytes 指定用于排序的主内存量，单位为 KB。 最小内存量总是 160 KB。如果指定内存大小， 无论主内存的可用量是多少，指定的内存量会 全部用于排序。 要取得最佳性能，通常不指定内存大小。按默认 值，如果达到默认最大内存值，排序会一次完成 (非临时文件)；否则，排序会分两次完成(没有 完全排序的数据存储在临时文件中)；用于排序 和合并的内存量相等。如果输入和输出都是文 件，默认最大内存量为可用主内存的 90%; 否则，为主内存的 45%。 |
SORT [/R] [/+n] [/M kilobytes] [/L locale] [/REC recordbytes] [[drive1:][path1]filename1] [/T [drive2:][path2]] [/O [drive3:][path3]filename3] /+n Specifies the character number, n, to begin each comparison. /+3 indicates that each comparison should begin at the 3rd character in each line. Lines with fewer than n characters collate before other lines. By default comparisons start at the first character in each line. /L[OCALE] locale Overrides the system default locale with the specified one. The \"\"C\"\" locale yields the fastest collating sequence and is currently the only alternative. The sort is always case insensitive. /M[EMORY] kilobytes Specifies amount of main memory to use for the sort, in kilobytes. The memory size is always constrained to be a minimum of 160 kilobytes. If the memory size is specified the exact amount will be used for the sort, regardless of how much main memory is available. The best performance is usually achieved by not specifying a memory size. By default the sort will be done with one pass (no temporary file) if it fits in the default maximum memory size, otherwise the sort will be done in two passes (with the partially sorted data being stored in a temporary file) such that the amounts of memory used for both the sort and merge passes are equal. The default maximum memory size is 90% of available main memory if both the input and output are files, and 45% of main memory otherwise. |
| 0x1CE9 | 输入记录超过最大长度。请指定更大的最大限度。 |
Input record exceeds maximum length. Specify larger maximum. |
| 0x1CEA | 无效的区域设置。 |
Invalid locale. |
| 0x1CEB | 排序位置必须大于零。 |
Sort position must be greater than zero. |
| 0x1CEC | 无效命令行开关。 |
Invalid switch. |
| 0x1CED | 记录数量最多不得超过 65535。 |
Record maximum cannot exceed 65535. |
| 0x1CEE | 输入文件指定了两次。 |
Input file specified two times. |
| 0x1CEF | 内部字符转换错误。 |
Internal character conversion error. |
| 0x1CF0 | 没有足够的内存，无法完成排序。 |
Not enough main memory to complete the sort. |
| 0x1CF1 | 警告: 大量排序时使用重定向的输入通常比指定输入文件名直接排序慢。 |
Warning: use of redirected input for large sorts is usually slower than specifying the input file name directly to sort. |
| 0x1CF2 | 警告: 做大量排序时使用重定向输出通常比直接指定输出文件名称来排序慢。 |
Warning: use of redirected output for large sorts is usually slower than specifying the output file name directly to sort. |
| 0x1CF3 | 警告: 该指定的内存大小过低，将被调整到最低值。 |
Warning: the specified memory size is too low and will be adjusted to the minimum. |
| 0x1CF4 | 警告: 该指定的内存大小已降低到可用的页面内存。 |
Warning: the specifed memory size is being reduced to the available paging memory. |
| 0x1CF5 | |
|
| 0x1CF7 | /REC[ORD_MAXIMUM] characters 指定记录中的最大字符数量 (默认值为 4096，最大值为 65535)。 /R[EVERSE] 颠倒排列顺序，即，从 Z 到 A，再从 9 到 0。 [drive1:][path1]filename1 指定要排序的文件。如果没有指定，则排序标准 输入。指定输入文件比将同一个文件重定向为标 准输入快。 /T[EMPORARY] [drive2:][path2] 指定保留排序工作存储的目录路径，以防主内 存无法容纳数据。默认值是使用系统临时目录。 /O[UTPUT] [drive3:][path3]filename3 指定在哪个文件中储存经过排序的输入。 如果没有指定，数据会被写入标准输出。指定 输出文件比将标准输出重定向到同一个文件快。 |
/REC[ORD_MAXIMUM] characters Specifies the maximum number of characters in a record (default 4096, maximum 65535). /R[EVERSE] Reverses the sort order; that is, sorts Z to A, then 9 to 0. [drive1:][path1]filename1 Specifies the file to be sorted. If not specified, the standard input is sorted. Specifying the input file is faster than redirecting the same file as standard input. /T[EMPORARY] [drive2:][path2] Specifies the path of the directory to hold the sort's working storage, in case the data does not fit in main memory. The default is to use the system temporary directory. /O[UTPUT] [drive3:][path3]filename3 Specifies the file where the sorted input is to be stored. If not specified, the data is written to the standard output. Specifying the output file is faster than redirecting standard output to the same file. |