If an error occurred or the following message in Chinese (Traditional) language and you cannot find a solution, than check answer in English. Table below helps to know how correctly this phrase sounds in English.
id |
Chinese (Traditional) |
English |
0x800503EA | IPMI 裝置驅動程式讀取到系統管理員所提供的不正確參數。裝置驅動程式將會使用系統所定義的預設值來替代。 |
The IPMI device driver read an administrator supplied parameter that is invalid. The device driver will use a system defined default value in its place. |
0x800503EC | IPMI 裝置驅動程式在正常操作時嘗試跟 IPMI BMC 裝置通訊。但是因為等候逾時,通訊失敗了。您可以增加 IPMI 裝置驅動程式的等候逾時時間。 |
The IPMI device driver attempted to communicate with the IPMI BMC device during normal operation. However the communication failed due to a timeout. You can increase the timeouts associated with the IPMI device driver. |
0xC00503E8 | 在跟 IPMI BMC 裝置通訊時,系統偵測到 BMC 進入了錯誤狀態。驅動程式嘗試將 BMC 狀態設定成處理狀態,但失敗了。在連續嘗試了 20 次後,驅動程式已將 IPMI 裝置設定成非處理狀態。建議您連絡 BMC 裝置製造商尋求協助。您可以停用及啟用標示為「IPMI 裝置驅動程式」的 IPMI 裝置執行個體,將裝置執行個體回復成處理狀態。您可以在裝置管理員使用者介面裡找到 IPMI 裝置執行個體。 |
During communication with the IPMI BMC device, the system detected that the BMC entered an error state. The driver attempted to set the BMC state to a working state but failed to do so. After 20 successive attempts, the driver has set the IPMI device to a non working state. It is recommended that you seek assistance from the BMC device manufacturer. You can return the device instance to the working state by disabling and enabling the IPMI device instance labeled ‘IPMI Device Driver’. You can locate the IPMI device instance within the Device Manager user interface. |
0xC00503E9 | IPMI 裝置驅動程式嘗試要判定是否系統能支援 IPMI BMC 裝置。驅動程式嘗試要透過搜尋 SMBIOS 裡的 Type38 記錄來偵測是否有 IPMI BMC 的存在。但是找不到記錄或者是記錄跟裝置驅動程式的版本不相符。如果偵測到 SMBIOS Type 38 記錄,事件的傾印資料欄位會包含記錄的數位代表。 |
The IPMI device driver attempted to determine if the system supported an IPMI BMC device. The driver attempted to detect the presence of the IPMI BMC by searching the SMBIOS for a Type38 record. But either no record was found or the record was not compatible with the version of the device driver. If a SMBIOS Type 38 record was detected, the Dump Data field of the event contains a binary representation of the record. |
0xC00503EB | IPMI 裝置驅動程式在裝置建立時嘗試跟 IPMI BMC 裝置通訊。但是因為等候逾時,通訊失敗了。要不設定的等候逾時值太小並且 IPMI BMC 裝置回應超過等候逾時時間,或者就是 BMC 有技術錯誤。您可以增加 IPMI 裝置驅動程式的等候逾時時間,或連絡 BMC 裝置製造商以取得協助。 |
The IPMI device driver attempted to communicate with the IPMI BMC device during device creation. However the communication failed due to a timeout. Either the configured timeouts are too small and the IPMI BMC device responses take longer than the timeouts or the BMC has a technical fault. You can increase the timeouts associated with the IPMI device driver or seek assistance from the BMC device manufacturer. |