| 0x40000020 | 发起程序收到异步注销消息。转储数据中给定了目标名称。 |
Initiator received an asynchronous logout message. The Target name is given in the dump data. |
| 0x40000022 | 对目标的连接丢失，但发起程序成功重新连接到目标。转储数据包含目标名称。 |
A connection to the target was lost, but Initiator successfully reconnected to the target. Dump data contains the target name. |
| 0x40000040 | 尝试使用 iSCSI NIC Boot (iBF)启动 Windows |
Attempt to bootstrap Windows using iSCSI NIC Boot (iBF) |
| 0x40000043 | 如果为 iSCSI 会话选择了 Digest 支持，则将对 Digest 计算使用 Processor 支持。 |
If Digest support selected for iSCSI Session, Will use Processor support for Digest computation. |
| 0x40000047 | 接收请求时，发起程序没有启动会话恢复。请转储包含错误状态的数据。 |
Initiator did not start a session recovery upon receiving the request. Dump data contains the error status. |
| 0xC0000001 | 发起程序无法连接到目标。转储数据中给定了目标 IP 地址和 TCP 端口号。 |
Initiator failed to connect to the target. Target IP address and TCP Port number are given in dump data. |
| 0xC0000002 | 发起程序无法为 iSCSI 会话分配资源。 |
The initiator could not allocate resources for an iSCSI session. |
| 0xC0000003 | 最大命令序列号不能连续大于登录响应中所需的命令序列号。转储数据包含所需的命令序列号，后跟最大命令序列号。 |
Maximum command sequence number is not serially greater than expected command sequence number in login response.Dump data contains Expected Command Sequence number followed by Maximum Command Sequence number. |
| 0xC0000004 | MaxBurstLength 不能连续大于 FirstBurstLength。转储数据包含 FirstBurstLength，后跟 MaxBurstLength。 |
MaxBurstLength is not serially greater than FirstBurstLength.Dump data contains FirstBurstLength followed by MaxBurstLength. |
| 0xC0000005 | 无法安装发起程序门户。转储数据中给定了错误状态。 |
Failed to setup initiator portal. Error status is given in the dump data. |
| 0xC0000006 | 发起程序无法为 iSCSI 连接分配资源 |
The initiator could not allocate resources for an iSCSI connection |
| 0xC0000007 | 发起程序无法发送 iSCSI PDU。转储数据中给定了错误状态。 |
The initiator could not send an iSCSI PDU. Error status is given in the dump data. |
| 0xC0000008 | 目标或发现服务未及时响应发起程序发出的 iSCSI 请求。转储数据中给定了 iSCSI 功能模式。有关 iSCSI 功能模式的详细信息，请参阅 iSCSI 用户指南。 |
Target or discovery service did not respond in time for an iSCSI request sent by the initiator. iSCSI Function code is given in the dump data. For details about iSCSI Function code please refer to iSCSI User's Guide. |
| 0xC0000009 | 目标未及时响应 SCSI 请求。转储数据中给定了 CDB。 |
Target did not respond in time for a SCSI request. The CDB is given in the dump data. |
| 0xC000000A | 登录请求失败。转储数据中给定了登录响应数据包。 |
Login request failed. The login response packet is given in the dump data. |
| 0xC000000B | 目标返回无效的登录响应数据包。转储数据中给定了登录响应数据包。 |
Target returned an invalid login response packet. The login response packet is given in the dump data. |
| 0xC000000C | 目标为登录重定向提供了无效的数据。转储数据包含目标返回的数据。 |
Target provided invalid data for login redirect. Dump data contains the data returned by the target. |
| 0xC000000D | 目标提供了未知的身份验证方法。转储数据包含目标返回的数据。 |
Target offered an unknown AuthMethod. Dump data contains the data returned by the target. |
| 0xC000000E | 目标为 CHAP 提供了未知的摘要算法。转储数据包含目标返回的数据。 |
Target offered an unknown digest algorithm for CHAP. Dump data contains the data returned by the target. |
| 0xC000000F | 目标给定的 CHAP 质询包含无效的字符。转储数据包含给定的质询。 |
CHAP challenge given by the target contains invalid characters. Dump data contains the challenge given. |
| 0xC0000010 | CHAP 协商过程中收到无效的密钥。转储数据中给定了 key=value 对。 |
An invalid key was received during CHAP negotiation. The key=value pair is given in the dump data. |
| 0xC0000011 | 目标给定的 CHAP 响应与所需的 CHAP 响应不匹配。转储数据包含 CHAP 响应。 |
CHAP Response given by the target did not match the expected one. Dump data contains the CHAP response. |
| 0xC0000012 | 发起程序需要标头摘要，但是目标没有提供。 |
Header Digest is required by the initiator, but target did not offer it. |
| 0xC0000013 | 发起程序需要数据摘要，但是目标没有提供。 |
Data Digest is required by the initiator, but target did not offer it. |
| 0xC0000014 | 对目标的连接丢失。发起程序将尝试重试连接。 |
Connection to the target was lost. The initiator will attempt to retry the connection. |
| 0xC0000015 | 标头中给定的数据段长度超过目标声明的 MaxRecvDataSegmentLength。 |
Data Segment Length given in the header exceeds MaxRecvDataSegmentLength declared by the target. |
| 0xC0000016 | 对给定的 PDU 检测到头摘要错误。转储数据包含该标头和摘要。 |
Header digest error was detected for the given PDU. Dump data contains the header and digest. |
| 0xC0000017 | 目标发送了一个无效的 iSCSI PDU。转储数据包含整个 iSCSI 标头。 |
Target sent an invalid iSCSI PDU. Dump data contains the entire iSCSI header. |
| 0xC0000018 | 目标发送了一个带有无效操作码的 iSCSI PDU。转储数据包含整个 iSCSI 标头。 |
Target sent an iSCSI PDU with an invalid opcode. Dump data contains the entire iSCSI header. |
| 0xC0000019 | 已检测到数据摘要错误。转储数据包含已计算的校验和，后跟给定的校验和。 |
Data digest error was detected. Dump data contains the calculated checksum followed by the given checksum. |
| 0xC000001A | 目标尝试发送多于发起程序所请求的数据。 |
Target trying to send more data than requested by the initiator. |
| 0xC000001B | 发起程序无法在收到的 PDU 中找到发起程序任务标记的匹配项。转储数据包含整个 iSCSI 标头。 |
Initiator could not find a match for the initiator task tag in the received PDU. Dump data contains the entire iSCSI header. |
| 0xC000001C | 发起程序收到一个无效的 R2T 数据包。转储数据包含整个 iSCSI 标头。 |
Initiator received an invalid R2T packet. Dump data contains the entire iSCSI header. |
| 0xC000001D | 目标拒绝了发起程序发送的 iSCSI PDU。转储数据包含被拒绝的 PDU。 |
Target rejected an iSCSI PDU sent by the initiator. Dump data contains the rejected PDU. |
| 0xC000001E | 发起程序无法分配用于处理请求的工作项。 |
Initiator could not allocate a workitem for processing a request. |
| 0xC000001F | 发起程序无法分配用于处理请求的资源。 |
Initiator could not allocate resource for processing a request. |
| 0xC0000021 | 目标给定的质询大小超过 iSCSI 规范中指定的最大值。 |
Challenge size given by the target exceeds the maximum specified in iSCSI specification. |
| 0xC0000023 | 目标 CHAP 机密比规范要求的最小大小(12 个字节)小。 |
Target CHAP secret is smaller than the minimum size (12 bytes) required by the spec. |
| 0xC0000024 | 发起程序 CHAP 机密比规范要求的最小大小(12 个字节)小。转储数据包含给定的 CHAP 机密。 |
Initiator CHAP secret is smaller than the minimum size (12 bytes) required by the spec. Dump data contains the given CHAP secret. |
| 0xC0000025 | 无法初始化 FIPS 服务。不会处理永久登录。 |
FIPS service could not be initialized. Persistent logons will not be processed. |
| 0xC0000026 | 发起程序要求用于登录身份验证的 CHAP，但目标未提供 CHAP。 |
Initiator requires CHAP for logon authentication, but target did not offer CHAP. |
| 0xC0000027 | 发起程序发送了一条重置目标的任务管理命令。转储数据中给定了目标名称。 |
Initiator sent a task management command to reset the target. The target name is given in the dump data. |
| 0xC0000028 | 目标要求通过 CHAP 进行登录身份验证，但未将发起程序配置为执行 CHAP。 |
Target requires logon authentication via CHAP, but Initiator is not configured to perform CHAP. |
| 0xC0000029 | 安全协商阶段，目标未发送身份验证方法密钥。 |
Target did not send AuthMethod key during security negotiation phase. |
| 0xC000002A | 目标为连接发送了一个无效的状态序列号。转储数据包含所需的状态序列号，后跟给定的状态序列号。 |
Target sent an invalid status sequence number for a connection. Dump data contains Expected Status Sequence number followed by the given status sequence number. |
| 0xC000002B | 目标无法及时响应登录请求。 |
Target failed to respond in time for a login request. |
| 0xC000002C | 目标无法及时响应注销请求。 |
Target failed to respond in time for a logout request. |
| 0xC000002D | 目标无法及时响应登录请求。该登录请求用于向会话添加新的连接。 |
Target failed to respond in time for a login request. This login request was for adding a new connection to a session. |
| 0xC000002E | 目标无法及时响应 SendTargets 命令。 |
Target failed to respond in time for a SendTargets command. |
| 0xC000002F | 目标无法及时响应通过 WMI 请求发送的 SCSI 命令。 |
Target failed to respond in time for a SCSI command sent through a WMI request. |
| 0xC0000030 | 目标无法及时响应 NOP 请求。 |
Target failed to respond in time to a NOP request. |
| 0xC0000031 | 目标无法及时响应任务管理请求。 |
Target failed to respond in time to a Task Management request. |
| 0xC0000032 | 目标无法及时响应发送至重新协商 iSCSI 参数的文本命令。 |
Target failed to respond in time to a Text Command sent to renegotiate iSCSI parameters. |
| 0xC0000033 | 目标无法及时响为响应来自目标的异步消息而发送的注销请求。 |
Target failed to respond in time to a logout request sent in response to an asynchronous message from the target. |
| 0xC0000034 | 发起程序服务无法及时响应为 iSCSI 连接配置 IPSec 资源的请求。 |
Initiator Service failed to respond in time to a request to configure IPSec resources for an iSCSI connection. |
| 0xC0000035 | 发起程序服务无法及时响应释放为 iSCSI 连接分配的 IPSec 资源的请求。 |
Initiator Service failed to respond in time to a request to release IPSec resources allocated for an iSCSI connection. |
| 0xC0000036 | 发起程序服务无法及时响应加密或解密数据的请求。 |
Initiator Service failed to respond in time to a request to encrypt or decrypt data. |
| 0xC0000037 | 发起程序无法分配向目标发送数据的资源。 |
Initiator failed to allocate resources to send data to target. |
| 0xC0000038 | 发起程序无法将用户虚拟地址映射到内核虚拟地址，从而导致发生 I/O 故障。 |
Initiator could not map an user virtual address to kernel virtual address resulting in I/O failure. |
| 0xC0000039 | 发起程序无法分配用于处理请求的资源，从而导致发生 I/O 故障。 |
Initiator could not allocate required resources for processing a request resulting in I/O failure. |
| 0xC000003A | 发起程序无法分配用于处理请求的标记，从而导致发生 I/O 故障。 |
Initiator could not allocate a tag for processing a request resulting in I/O failure. |
| 0xC000003B | 目标丢弃连接之后，发起程序才能转换为工作阶段。 |
Target dropped the connection before the initiator could transition to Full Feature Phase. |
| 0xC000003C | 目标在 SCSI Response PDU 而非 Data_IN PDU 中发送数据。仅感知数据能在 SCSI Response 中发送。 |
Target sent data in SCSI Response PDU instead of Data_IN PDU. Only Sense Data can be sent in SCSI Response. |
| 0xC000003D | 当发起程序请求“是”时，目标将 DataPduInOrder 设置为“否”。登录将失败。 |
Target set DataPduInOrder to NO when initiator requested YES. Login will be failed. |
| 0xC000003E | 当发起程序请求“是”时，目标将 DataSequenceInOrder 设置为“否”。登录将失败。 |
Target set DataSequenceInOrder to NO when initiator requested YES. Login will be failed. |
| 0xC000003F | 无法重置目标或 LUN。将尝试会话恢复。 |
Can not Reset the Target or LUN. Will attempt session recovery. |
| 0xC0000041 | 正在从 iSCSI 启动，但无法设置分页路径中的任何 NIC。 |
Booting from iSCSI, but Could not set any NIC in Paging Path. |
| 0xC0000042 | 尝试禁用 iSCSI 连接的 Nagle 算法失败。 |
Attempt to disable the Nagle Algorithm for iSCSI connection failed. |
| 0xC0000044 | 从目标接收异步注销后，尝试再次登录会话失败。转储数据中给出错误状态。 |
After receiving an async logout from the target, attempt to relogin the session failed. Error status is given in the dump data. |
| 0xC0000045 | 尝试恢复意外终止的会话失败。转储数据中给出错误状态。 |
Attempt to recover an unexpected terminated session failed. Error status is given in the dump data. |
| 0xC0000046 | 处理 iSCSI 登录请求时发生错误。未重试该请求。转储数据中给出了错误状态。 |
Error occurred when processing iSCSI logon request. The request was not retried. Error status is given in the dump data. |
| 0xC0000048 | 非预期的目标门户 IP 类型。转储数据包含预期的 IP 类型。 |
Unexpected target portal IP types. Dump data contains the expected IP type. |