| 0x1 | 由于 BIOS 配置问题，高精度事件计时器的初始化失败。%n操作系统将使用其他可用的平台计时器代替高精度事件计时器。%n%n请与系统供应商联系以获得技术帮助。%n初始化状态: %1。 |
Initialization of the High Precision Event Timer failed due to a BIOS configuration problem.%nThe operating system will use another available platform timer in lieu of the High Precision Event Timer.%n%nContact your system vendor for technical assistance.%nInitialization status: %1. |
| 0x2 | 由于不受支持的硬件，高精度事件计时器的初始化失败。%n操作系统将使用其他可用平台计时器代替高精度事件计时器。%n%n初始化状态: %1。 |
Initialization of the High Precision Event Timer failed due to unsupported hardware.%nThe operating system will use another available platform timer in lieu of the High Precision Event Timer.%n%nInitialization status: %1. |
| 0x3 | 由于中断配置问题，高精度事件计时器的初始化失败。%n操作系统将使用其他可用的平台计时器代替高精度事件计时器。%n%n使用更新的系统 BIOS 可能会解决此问题。%n请与系统供应商联系以获得技术帮助。%n初始化状态: %1。 |
Initialization of the High Precision Event Timer failed due to an interrupt configuration problem.%nThe operating system will use another available platform timer in lieu of the High Precision Event Timer.%n%nIt may be possible to address this problem with an updated system BIOS.%nContact your system vendor for technical assistance.%nInitialization status: %1. |
| 0x4 | 由于意外情况，操作系统将使用另一个可用平台计时器来代替处理器的周期计数器。 状态: %1。 |
Due to an unexpected condition, the operating system will use another available platform timer in lieu of the processor's cycle counters. Status: %1. |
| 0xB | High Precision Event Timer 无法发送信号中断的消息。操作系统将回退到该计时器的基于行的中断。%n初始化状态: %1。 |
The High Precision Event Timer failed to deliver message signalled interrupts. The operating system will fall back to line based interrupts for this timer.%nInitialization status: %1. |
| 0xC | 在整个以前的系统电源转换中平台固件已损坏内存。请检查系统的更新固件。 |
The platform firmware has corrupted memory across the previous system power transition. Please check for updated firmware for your system. |
| 0xD | 系统监视器计时器被触发。 |
The system watchdog timer was triggered. |
| 0x50000002 | 错误 |
Error |
| 0x50000003 | 警告 |
Warning |
| 0x50000004 | 信息 |
Information |
| 0x50000005 | 详细 |
Verbose |
| 0x90000001 | Microsoft-Windows-HAL |
Microsoft-Windows-HAL |
| 0x90000002 | System |
System |
| 0x90000003 | Microsoft-Windows-HAL/Debug |
Microsoft-Windows-HAL/Debug |
| 0xB0000007 | 处理器 %1 已探测到处理器 %2 上的处理器周期计数器。 已检测到计数器增量 %3。 已检测到这些处理器之间的通信延迟大约为 %4。 |
The processor cycle counter on processor %2 has been probed by processor %1. A counter delta of %3 was detected. The approximate communication delay between these processors was detected to be %4. |
| 0xB0000008 | 已在可接受的操作阈值范围内从处理器 %1 成功同步了该处理器的周期计数器。 检测到的最大正增量为 %3，最大负增量为 %4。 同步已执行了 %5 微秒。 |
The processor's cycle counters have been successfully synchronized from processor %1 within acceptable operating thresholds. The maximum positive delta detected was %3 and the maximum negative delta was %4. Synchronization executed for %5 microseconds. |
| 0xB0000009 | 使用第 %5 次尝试的 %4 个周期调整根据处理器 %1 同步处理器 %2 上的处理器周期计数器。 这将产生 %3 个周期的增量。 |
The processor cycle counter on processor %2 was synchronized against processor %1 using an adjustment of %4 cycles on attempt %5. This resulted in a delta of %3 cycles. |
| 0xB000000A | 同步处理器的周期计数器时未能在可接受的操作阈值范围内同步处理器。 状态: %1。 |
The synchronization of the processor's cycle counters was not able to synchronize the processors within acceptable operating thresholds. Status: %1. |
| 0xB000000E | 已触发监视器唤醒计时器。 |
The watchdog wake timer was triggered. |